Is my pool compatible?

The system will work on all pools and spas providing

the filtration is specified to local standards.

Do I need to add chemicals?

We suggest to add an initial dose of sodium

hypochlorite (Chlorine liquid) to raise the chlorine

level to 1.5 ppm as an initial reference point. This

also ensures that new built pool have adequate

sanitation through stagnant pipework.

What Acid do I need?

The system automatically regulates the pH levels by

dosing liquid acid – we suggest to use 10%

Hydrochloric acid available from your local pool

supplier.

How much salt do I add?

The system will also require Fine granular salt to

assist with conductivity across the Hydrolysis cell

and allow the system to generate a low residual

sanitation of the pool water. The suggested amount

of salt is 1-3.5 grams / litre depending on the system

specified.

Can I use my waste water for irrigation?

Absolutely! Providing the system is maintained on a

low level salt concentration (Pro-UV and Pro-Oxi)

then backwash water can be recycled to water the

plants and grass.

Can I discharge my waste water

into the mains drainage?

Sure, there is no problem at all with routine filter

maintenance, back washing and rinsing into the

mains drainage.

What is the electrical requirement?

The control box will run off a 6amp C type MCB. If

being used as a slave system this should be

interlocked with the filter pump. If full benefit of the

con troll system is being used, a 6amp supply with

a 3amp control circuit is required. We advise that

our expertise is used with integration to existing

pool control systems.

Physical set up:

Plant integration;

Two options:

Slave unit (simply stand-alone dosing and monitor) Master control

system (will need interface panel or existing panel modifications)

Utilising I/O functions. Filter pump control plus variable speed if

fitted. Heating control water only. Lighting control plus colour

change led if fitted. AHU systems will still need to control air temp

and humidity however water stat should be connected as hi-limit.

Pipework comes in metric 63mm as standard although the UV has

2” / 63mm options. The included special 1/2” Adaptors have 50mm

(female) internal and 63mm external (male) solvent weld ends.

We use saddle Clamps where possible as a preference as this

saves time and gives us more versatility to site the fittings.

Flow to the offline sample Line is usually taken post filter to

eliminate the pre filter getting blocked when vacuuming the pool.

The return is brought back into the inlet manifold.

The temperature stat can be anywhere as long as it is pre-heating.

The UV is best sites post filter either before or after the heating, but

it is entirely necessary to install the hydrolysis cell last in line. This

is essential for preventing any electrolytic damage to the heating

mechanism of the pool. The acid line is injected directly to this cell

to assist with cleaning.

Sometimes the end user will notice that there are white crystals

appearing in the pool. This is a giveaway sign that the water

balance is incorrect and there are high calcium salts present. If

consistently appearing there may be more sinister issues such as

the pool is losing water. This has highlighted many leaking pool

issues!

Water balalance is critical;

Before installation and setup, we advise that the pool is initially

balanced as follows: Ph 7.1-7.4

Alkalinity 100-160 depending on pool finish Calcium 350-450

Free chlorine 1-2ppm as an initial level to identify our desired RX set

point. Salt 1-1.5g/l

Do not use clarifiers as these can foul the probes.

Control:

The system can be used as a slave (plug in) chemistry control system

but has far more relevance as a full control system. Simply Interfacing

via the Electair panels either option of a new build specification or a

retro fit integration panel. Panels can be custom built according to the

actual plant specification normally within the order to delivery time for

the manufacture of the SV.

DATA Logging:

The ProSV allows for the end trade installer to quantify warrantee

claims from the end user by Supporting evidence on warrantee issue

for instance liner at Yates, Heatstar heat exchangers.